DOOR OPERATORS

TORMAX TTX II

tormax logo

TTX II Side and Bottom Load Design (Low Energy)

The new TTX II low energy swing door operator is a low cost, easily adjustable automatic door system. It delivers exceptional long lasting performance, and meets ANSI standard A156.19 that specifies opening and closing speeds as well as force requirements. This non-handed power open, spring close operator is applicable to interior and exterior doors up to 48" wide and weighing up to 220 pounds. Using reliable rack and pinion mechanics and state-of-the-art digital programmable microprocessors, the TTXII is the best solution on the market for conformance with ADA (Americans with Disabilities Act) requirements. Available in both Side and Bottom Load Design.

First Class with Luxury Features!

By means of the user-friendly teach-in program you can dial-in the drive to meet your specific application requirements. At what speed should the door open? How wide should it open? How long should it remain open? How fast should it close? All this is done without a single additional setting device. The Tormax TTX II Swing Door Operator is the all-in-one drive of superior Tormax quality and unmatched features.

Side Load Design

Overhead lintel mounted for quick and easy installation. Side load design provides for convenient operator access from header face.

The door cannot be free-wheeled in windy conditions because the operator employs a unique rack and pinion compression spring design. Also, a unique conical/hexagonal shaped output shaft design eliminates arm slippage and minimizes costly repairs commonly found on competitive operators. Design control feature will accommodate 24 VDC radio control receivers, push plates, operate and safety sensors, as well as 24 VDC electric strikes and magnetic locks.

TORMAX Technologies offers a comprehensive line of automatic door systems including slide door systems, swing door systems and industrial door systems. TORMAX products are available throughout North America through authorized TORMAX Technologies distributors.

For buildings that meet the Historic Preservation Society guidelines, specify the Tormax TN concealed in-floor low energy swing door operator.

To find out more about the TTX II low energy swing door operator, other TORMAX products, or the MAX national and regional account program, please contact us for immediate attention.

Bottom Load Design 

The new TTX II Bottom Load unit provides the solution to maintaining the Architectural design for applications that have little or no headroom above the door. The operator is accessible from the underside, thus allowing for the header case to be partially or fully concealed into the ceiling above the door.

Tormax TTXII Bottom and Side Load
Tormax-TTXll-Side-Load
Tormax TTXII Side Load
Tormax-TTXll-Bottom-Load
Tormax TTXII Bottom Load

Wireless or Manual Control

For added convenience and accessibility the door operator can be activated by a push button switch, a manual push or pull of the door "Push and Pull", a remote control or simply use it as a manual door. This creates a barrier free access to assist the physically challenged.

Manual Controls:
  • Push Plate
  • Push Pads
  • Push Buttons
Wireless Manual Controls:
  • Push Plate
  • Push Buttons
  • Hand Held Transmitters
 

Mechanical Operator Feature Benefit

  • Non-Handed Electro-Mechanical Operator Reduces on Hand Inventory
  • Power Open Spring Close - Functions as a Manual Door Closer With Loss of PowerRack and Pinion With Compression Spring Design Eliminates Free-Wheeling of the Operator in Windy Environments
  • Unique Re-Circulating Ball Screw Drive - Provides the Ultimate in Automatic and Manual Door Control (no gears to wear or leaking oin
  • Fractional DC Motor With Built-In Motor Protection Circuit - Interrupts Current to Motor if Door is Blocked
  • Rubber Pads Isolate the Operator Mechanism From the Aluminum Back Plate - Provides for Smooth and Silent Operation (less than 70 DB)
  • Unique Conical/Hexagonal Shaped Stainless Steel Output Shaft- Eliminates Door Arm Slippage
  • Rated for Interior and Exterior Doors up to 48" Wide x 220 Lbs.
  • Factory Assembled, Tested and Shipped as a Complete Unit
  • Models Available to Automate Single, Simultaneous Pair and Double Egress Applications
  • Side Load Back Plate Design (SL) - Factory Prepared for Quick and Easy Installation
  • Side Load Design (SL) - For Convenient Operator Access
  • Durable Steel End Plates (SL) - For Structural Integrity
  • Compact Visible Side Load Design (SL) - Header Profile 4 9/16" H X 5" W X 31 1/2" L
  • Optional Bottom Load Design (BL) - The Ultimate Solution to Maintaining the Architectural Design for Doors That Have Little or No Head Room
  • Bottom Load Design (BL) - Factory Prepared for Quick and Easy Installation
  • Operator is Accessible From the Underside (BL) - Allows for the Header Case to be Partially or Fully Concealed Into the Ceiling Above the Door
  • Aluminum "L" End Cap Mounting Brackets (BL) - For Ease of Unit Mounting
  • Compact Visible Bottom Load Design (BL) - Header Profile 5 3/4" H X 5 1/2" W X 31 1/2" L
  • Built-In Adjustable Operator End Stop - No External Door Stop Required
  • Three Operating Modes (On/Off/Hold Open) - Pre-wired Switch as Standard With Each Unit
  • No Mechanical Switches and/or Magnets Required for Door Position - Eliminates Costly Services and Down Time

Digital Microprocessor Controller Feature Benefit

  • Microprocessor Controller With On-Board Digital Programming
  • Electronic Reversing for Door Obstruction in the Opening Direction and Closing Direction
  • Selectable (on/off) "Push and Pull" Operation
  • Primary "Teach-In" Self-Learning Program for "Push and Pull" and Automatic Door Operation. Establish Door Opening and Closing Speeds, Opening Angle and Hold Open Time by Manually Opening and Closing the Door
  • Establish Separate and Unique Door Operating Parameters for "Push and Pull" and Automatic Door Operation Through a Secondary "Teach-In" Self-Learning Program.
  • Fine-Tune Door Motion Elements (door speeds, opening angle and hold open time 0-6000s) Independently After "Teach-In".
  • Adjustable Latch Check Speed Positioning
  • Adjustable Opening Force Limitation
  • Adjustable Opening and Closing Speed Limitation
  • Sequential Operation (Push to Open/Push to Close)
  • On-Board Power Supply Output With Overload Protection (24VDC. 75A Max.) for Radio Control Receiver - No Auxiliary Transformer Required
  • On-Board Output for 24VDC Electric Strike With Adjustable (.2-3.6S) Delay
  • On-Board Output for 24VDC Magnetic Lock
  • On-Board Output for Door Open or Door Closed Position Status
  • On-Board Input for Key Switch
  • On-Board Inputs for Swing Side and Approach Side Door Mounted Presence Sensors, Swing Side Overhead Mounted Presence Sensor and Swing Side Door Mounted Presence Sensor or Safety Carpet
  • Built-In Safety Circuit With Stall Logic - No Auxiliary Modules Required
  • Global Power Supply - Selectable 115-230VAC 50- 60 HZ, Single Phase
 

Need a fast quote for an upcoming project?

Contact Us For A Sameday Quote!

Downloads

For a full list of brochures, drawings & specifications visit

Downloads Page

Quality Assurance

When you choose Niagara Belco you choose quality. Niagara Belco products are built by elevator people with elevator know-how. A commitment to excellence and hands on project management from start to finish is our pledge to you. Make Niagara Belco products a successful part of your next project, your satisfaction is guaranteed!

Warranty

Niagara Belco stands by all their products and offers a limited 2-year & 5-year warranty* on all major components and a lifetime warranty on all structural components.

*For complete warranty details view Warranty pdf
warranty 2 year warranty 5 year warranty Lifetime
 

Contact Niagara Belco

Toll-free 1-888-465-9999
Telephone: 905-526-9727
Fax: 905-526-0258

Email: sales@niagarabelco.com

Mailing Address:

Niagara Belco Ltd
PO box 900 Stn LCD 1
Hamilton, Ontario
L8N 3P6
Canada

Certified & Respected

Niagara Belco, is a member of the National Association of Elevator Contractors (N.A.E.C.) and the Canadian Elevator Contractors Association (C.E.C.A.) since 1984.

National Association of Elevator ContractorsCECA ACEA